(712) Bath Basics
Design and Decor, Featured, Flooring, Kitchens and Baths, Plumbing, Repairs and Installation, Today's Homeowner by Danny Lipford
Danny has remodeled a lot of bathroom over the years, but this job is personal, since it’s in his own home. What started as a simple upgrade, expanded into a complete bathroom renovation that included replacing the tub surround and tile floor, upgrading the plumbing and faucets, and installing a new vanity and accessories.
Danny’s bathroom before remodeling.
Demolition
Work began by tearing out a built-in closet and removing the existing pedestal sink. Next, the 20-year-old cultured marble tub surround was removed, along with the tile floor. In addition, part of the engineered wood floor in the powder room had to be replaced to cover the area occupied by the closet.
Wiring
Replacing the two wall scones over the sink with a single light fixture required cutting a new hole in the drywall, rerouting the wires, and repairing the holes in the existing drywall.
Wiring Tip
Always use an electrical tester to check for hot wires, and turn off the circuit breaker before working on the wiring in your home. Non-contact testers can detect electrical current without actually coming in contact with a bare wire.
Plumbing and Fixtures
The faucets for the tub and sink have an oil rubbed bronze finish and are from the Vestige collection by Moen. The tub faucet includes a pressure balance valve that automatically adjusts to changes in water pressure to maintain constant water temperature and prevent scalding.
Flexible PEX pipe was used to connect the existing polybutylene water lines to the copper pipes on the new faucets.
Tile Floor and Shower Surround
Once the plumbing had been roughed in, cement backer board was attached to the studs around the tub. A plastic pan was screwed to a cutout in the backer board to form a recess to accommodate shampoo and soap.
Seams in the backer board were covered with mesh tape and coated with thin-set. Before the tile were laid, the shower walls were coated with a waterproofing compound—such as Durex Blue Shield from Durabond Products or RedGard by Custom Building Products—to prevent moisture from penetrating through the tile or grout. The concrete floor was primed as well, and a floor leveling compound was poured on the slab to make sure it was flat and smooth.
Rather starting the first row of tile on the tub, guide boards were attached to the shower walls to provide a level support for the tile. To minimize the size of the grout lines, toothpicks were used as spacers between the tile.
The walls of the tub surround were tiled with 12”x 12” Crema Cappuccino tiles from The Home Depot. Moroccan Desert mosaic blend glass tile from the Tessera collection by Oceanside Glasstile were used for the bathroom floor and accent band around the tub surround.
Tiling Tip
When applying thin-set adhesive with a notched trowel, use a trowel with small notches for small tile and large notches for large tile.
After the tile adhesive had set, the paper backing on the mosaic tile was peeled off, and grout was applied to the joints with a float. Darker colored grout was used on the mosaic tile floor and accent band, with a lighter grout for the tub surround.
Bathroom Vanity
Once the drywall in the powder room had been repaired, the walls were painted. When all the work was finished, a Socotra vanity with a black Galaxy Granite top and white oval sink was set in place and the plumbing attached.
After a little clean up and decorating, Danny’s bath renovation was complete.
Other Tips from This Episode
Simple Solutions with Joe Truini:
Homemade Tile Snapping Jig
When scoring and snapping tile, it can be hard to break off a small strip. To solve this problem, sandwich a strip of plywood the thickness of the tile between two 1×4s. Clamp the jig to a workbench, and insert the tile so the scored line is flush with the jig. Tighten the clamps, and press down on the tile to snap it cleanly. Watch This Video
Best New Products with Jodi Marks:
SharkBite Plumbing Fitting
SharkBite push-fit plumbing fittings can be used to join copper, CPVC, or PEX pipe without gluing or soldering. Simply push the pipe on the fitting, and you’re done. A special tool is available to remove the fitting for disassembly. SharkBite tees, elbows, couplings, and adaptors for 1/2″ and 3/4” pipe are available at The Home Depot.
Watch This Video
Thinking Green:
Mercury in CFL Bulbs
There has been much concern expressed over the mercury found in compact fluorescent light bulbs, but the amount of mercury in each bulb is so small that it would fit on the tip of a pencil. As long as you dispose of burned out or broken CFLs properly, they shouldn’t pose a problem.
Watch This Video
3 Comments on “(712) Bath Basics”
You can follow comments to this article by subscribing to the RSS news feed with your favorite feed reader.
Leave a Comment
Comments submitted may be edited for clarity and used on Homefront, Today’s Homeowner®, or posted in articles on dannylipford.com at our discretion. In addition, you may submit questions at our contact page or by calling (800) 946-4420.
February 20th, 2010 at 07:05
I watch alot of your programs. I need some advise obout repairing ceramic floor tiles and if you know what might be causing this problem. We live in South West Louisiana. The house that we bought was 5 yrs. old. Now it is 10-yrs old and it has a slab floor.
After hurricans Rita & Ike. We have noticed that when the temperatures go to around freezing and then start to warm up. Our (12″ x 12″)floor tiles, in different areas of the house, are coming loose, cracking & even buckling. I looked out side for cracks in the foundation and did not see any. The tiles have a grey colored adhesive under them. It looks like some kind of grout cement.
Do you know what causes this? How can I fix this problem?
March 3rd, 2010 at 04:16
I am an amateur handyman and grandfather of three, I got to get my 4 month old grandson to start watch your videos. Great stuff, I really like the jig for snapping the tile on narrow cuts.
Thanks,
Chuck
May 10th, 2010 at 13:37
May 9, 2010 show -33936 zip code area; you had a show that you used car wax for waxing 1/3 of the shower stall, but what did you use to clean the shower stall? Also, the shower door you sprayed it with rain-x, but what did you clean the shower door with to remove the soap scum?